Contact us
for pricing or information on pullers and grips not
listed here.
Inner Duct Puller
Designed to install Polyethylene Ducting using a screw-in tapered
buttress thread to grip the Inside diameter of the duct.
Also called the
Screw-in or Carrot Pulling Eye, this is one of the most commonly
used types of pulling device. It has a simple, inexpensive,
one-piece construction with two flutes designed to actually cut a
thread in the bore of the duct as it is screwed in. Virtually
impossible to pull out, this product is hard to beat.
Designed to
grip polyethylene ducting using expanding jaws to grip the
inside wall of the duct. This causes the pulling load to be
spread around the circumference of the duct and allows a maximum
load to be applied without damage to the ducting.
On thin wall
ducting, it is recommended that an outer Duct Sleeve be used to
prevent the duct from stretching during installation.
Use of a
duct plugger will help prevent mud and slurry from entering past
the puller into the ducting.
Standard Expanding Pullers
Part
Description
Fits
US $
1601-100-01
Standard Expanding Puller (1-1/4")
1.29 to 1.50 ID
135.00
1601-100-02
Standard Expanding Puller (1-1/2")
1.60 to 1.68 ID
163.00
1601-100-03
Standard Expanding Puller (2")
1.88 to 2.12 ID
211.00
1601-100-04
Standard Expanding Puller (2-1/2")
2.25 to 2.50 ID
287.00
1601-100-05
Standard Expanding Puller (3")
2.75 to 3.06 ID
335.00
1601-100-06
Standard Expanding Puller (4")
3.50 to 4.06 ID
405.00
1601-100-07
Standard Expanding Puller (5")
4.50 to 5.00 ID
600.00
1601-100-08
Standard Expanding Puller (6")
5.44 to 6.12 ID
730.00
1601-100-09
Standard Expanding Puller (8")
6.44 to 7.87 ID
919.00
Pullers
Expanding Puller
Also available in
larger sizes and 00621 metric series.
Manufactured of
Hi-Fatigue plastic coated Aircraft Strand steel cable in various
weave designs. Recommended wherever high strength and small size are
required. Patented pulling eye is flexible and stress relieving.
Wire Mesh Pulling Grips
Part
Description
Fits
US $
1603-100-01
Wire Mesh Pulling Grip (0.75" to 1.12", Double Weave, 24"L)
6,700 lb
68.00
1603-100-02
Wire Mesh Pulling Grip (1.18" to 1.49", Double Weave, 24"L)
10,000 lb
75.00
1603-100-03
Wire Mesh Pulling Grip (1.50" to 1.99", Double Weave, 24"L)
16,400 lb
85.00
1603-100-04
Wire Mesh Pulling Grip (2.00" to 2.49", Triple Weave, 24"L)
18,500 lb
112.00
1603-100-05
Wire Mesh Pulling Grip (2.50" to 2.99", Triple Weave, 36"L)
24,500 lb
130.00
1603-100-06
Wire Mesh Pulling Grip (3.00" to 3.74", Triple Weave, 36"L)
24,500 lb
145.00
1603-100-07
Wire Mesh Pulling Grip (3.75" to 4.24", Triple Weave, 48"L)
31,000 lb
160.00
1603-100-08
Wire Mesh Pulling Grip (3.75" to 4.99", Triple Weave, 48"L)
